Many solid state detectors are not limited by their intrinsic rate capability, but by the readout system connected to them. The Quantum Detectors Xspress 3 was developed to maximise the throughput and resolution of such detectors and remove the bottleneck at the readout stage. With output count rates of over 3 Mcps, this detector is easily 10X faster than the systems many users have on their beamlines. Xspress 3 can open up the beamline to much faster data collection, its dynamic range can reduce the number of scans required and save large amounts of time with attenuation selection.
The XSPRESS3 system contains a Xilinx Virtex-5 FPGA with two embedded PowerPC processors. PPC1 manages the DMA engines. PPC2 runs the Xilinx micro kernel and communicates to the Intel 64 bit Linux server PC by 1 GBit Ethernet,TCP sockets. Bulk data and event lists to be histogrammed are sent from the firmware to the Server PC by 10G Ethernet, UDP.
The Software Development Toolkit (SDK) is provided for Linux only.
Unpack the SDK distribution into either the
camera/xspress3/sdk directory or
/usr/local/lib. Then ensure the libraries are in the
The SDK has shared libraries which has been compiled on recent linux kernel. g++ (GCC) 4.1.2 20080704 (Red Hat 4.1.2-50), check first you have the right kernel and libc available by compiling the test program.
The default network setup is (excluding the site network connection):
1GBit Copper network for control communinication between the PC and the XSPRESS3 box. With more than 1 XSPRESS3 box connected this network uses a ethernet switch A private network with 64 addresses allocated:
$ ifconfig eth1 eth1 Link encap:Ethernet HWaddr d4:ae:52:7d:5f:84 inet addr:192.168.0.1 Bcast:192.168.0.63 Mask:255.255.255.192 inet6 addr: fe80::d6ae:52ff:fe7d:5f84/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:1567 errors:0 dropped:5766 overruns:0 frame:0 TX packets:158 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:173937 (169.8 KiB) TX bytes:37252 (36.3 KiB) Interrupt:48 Memory:da000000-da012800
A 10GBit Fibre network for data transfer, point to point with 4 addresses allocated. With more that 1 XSPRESS3 box there would be multiple 10G Ports on the PC with multiple 4 address range subnets:
$ ifconfig eth2 eth2 Link encap:Ethernet HWaddr 00:07:43:05:7c:65 inet addr:192.168.0.65 Bcast:192.168.0.67 Mask:255.255.255.252 inet6 addr: fe80::207:43ff:fe05:7c65/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:702 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:154963 (151.3 KiB) Interrupt:41 Memory:dd7fe000-dd7fefff
Note the carefully picked subnet masks etc and the MTU 9000 We then have a script that should be executed automatically at boot.
$ cat /etc/init.d/xspress3.sh #!/bin/bash # # static-arp This is to register a static ARP address in the arp table at boot # # Kept as simple as possible hopefully this will auto register the associated # MAC with the private network address to allow the machine to communicate with the # test boards for xspress3 # Derived from work by Duncan Russell, by William Helsby PATH=/sbin:/bin:/usr/bin:/usr/sbin arp -i eth2 -s 192.168.0.66 02:00:00:00:00:00 #route -v add -host 192.168.0.66 eth2 # Setting default and max buffer sizes for networking. sysctl -w net.core.rmem_max=1073741824 sysctl -w net.core.rmem_default=1073741824
Installation & Module configuration¶
Follow the generic instructions in Build and Install. If using CMake directly, add the following flag:
For the Tango server installation, refers to PyTango Device Server.
Initialisation and Capabilities¶
In order to help people to understand how the camera plugin has been implemented in LImA this section provide some important information about the developer’s choices.
The camera will be initialized within the
Xspress3::Camera object. A TCP socket connection on the 1GBit port is established and optionally a UDP connection on the 10Gbit port (depends on boolean constructor flag noUDP). The ROI’s are reset, the first card in a multicard system or the single card, is set to be the master and the run flags are set to initiate Scaler and Histogram modes. The register and configuration settings (as optimised by QD on delivery) are uploaded to the Xspress3.
The Xspress3 requires the following parameters with the recommended settings:
nbCards = 1 (number of Xspress3 boxes) maxFrames = 16384 baseIPaddress = "192.168.0.1" basePort = 30123 baseMACaddress = "02.00.00.00.00.00" nbChans = 4/6/8 (depends on the firmware) createScopeModule = true/false scopeModuleName = "a-name-of-your-choice" debug = 0 is off, 1 is on, 2 is verbose cardIndex = 0 (for a 1 xspress system) noUDP = true/false directoryName = "directory containing xspress3 configuration settings"
Xspress3::Camera contructor sets the camera with default parameters for Number of Pixels (4096), the imageType (Bpp32),
Number of Frames (1) and the trigger mode (IntTrig)
This plugin has been implemented with respect of the mandatory capabilites but with some limitations which are due to the camera and SDK features. We only provide here extra information for a better understanding of the capabilities for Xspress3 cameras.
getCurrImageType/getDefImageType(): is set to Bpp32
setCurrImageType(): will not change the image type.
getMaxImageSize/getDetectorImageSize(): is defined as number of pixels + number of scalers x number of channels, i.e. (4096+8) x 4 for a 4 channel xspress3 system
getPixelSize(): is hardcoded to be 1x1
getDetectorModel(): reads and reports the xspress3 firmware version.
get/setTrigMode(): the only supported modes are IntTrig, ExtGate and IntTrigMult
The raw data is saved in .edf file format. Each frame is saved as it completes. To allow Lima to save both histogram and scaler data, the latter is appended to the histogram data.
histogram scaler  [0 ... 4095, 4096 ... 5003] channel 0  [0 ... 4095, 4096 ... 5003] channel 1  [0 ... 4095, 4096 ... 5003] channel 2  [0 ... 4095, 4096 ... 5003] channel 3
Camera::readScalers(): returns the raw scaler data from the Lima buffers from the specified frame and channel
Camera::readHistogram(): returns the raw histogram data from the Lima buffers from the specified frame and channel
Camera::getUseDtc(): set to true will dead time correct the data returned from the Lima buffers (default is false)
Camera::getUseHw(): set to true will return raw histogram data from the H/W data buffers, including the current frame.
How to use¶
See example in the test directory. Playback data should be extracted from the tarball.