Installation of PSI/Eiger embedded server and firmwares
Requirements
The following elements are required in order to perform an upgrade of the PSI/Eiger embedded server and firmwares (FWs):
The detector names are expected to be in registered in the hosts name service (/etc/hosts, DNS), and reachable through the IPv4 layer.
The GitLab Hardware/sls_detectors project is expected to be installed in ${SLS_DETECTORS_DIR} (defaults to ~blissadm/local/sls_detectors). The different Git submodules are recursiverly cloned, so slsDetectorFirmware and Lima/camera/slsdetector/slsDetectorPackage are available.
The ${SLS_DETECTORS_DIR}/common/scripts/det_env_setup.sh is available and sourced, defining LIMA_DIR, SLS_DETECTOR_NAME, SLS_DETECTOR_CONFIG, SLS_DETECTOR_MODULES, SLS_DETECTOR_LOG and SLS_DETECTOR_BACKEND_SETUP
Please refer to Installation of Eiger computer at ESRF in order to fulfill these requirements.
SSH keys
Backup the current PSI/Eiger-500k modules Linux root account SSH authorized_keys and check that the opid00@lisgeiger1 SSH public key is included:
lisgeiger1:~ % \
[ -n "${SLS_DETECTOR_MODULES}" ] || . ${SLS_DETECTORS_DIR}/common/scripts/det_env_setup.sh
EIGER_MODULE_TOP=$(echo ${SLS_DETECTOR_MODULES} | cut -f1 -d" ")
cat ${SLS_DETECTORS_DIR}/eiger/ssh/id_dsa.pub
echo
base_dir="${SLS_DETECTOR_LOG}/${SLS_DETECTOR_NAME}"
this_dir="${base_dir}/$(date +%Y-%m-%d-%H%M)"
mkdir -p ${this_dir} && cd ${this_dir}
for m in ${SLS_DETECTOR_MODULES}; do
ssh -x root@${m} cat .ssh/authorized_keys > ssh_authorized_keys_${m}
done
cat ssh_authorized_keys_${EIGER_MODULE_TOP}
ssh-dss AAAAB3NzaC1kc3MAAACBALGVR0qC2i/HgaJl4fuiwmOVrq46Bz3bs+o3/jdw/dqMaPjx35Ha
shyC4zS+2wHyZVSjwTMIbVT8LPsNMGxL40ZxqWaAUyzn0XnjJMe3XT7h+yyx+iLUXvyCK489PAwT0srE
iWbGNeQTgEYiwX+jqezQTiwss2sgypOrrwIrGrZBAAAAFQDjOUdgHjbCc1UMW37Zu+7b/AV1cQAAAIAu
tumVMJlCqWv30RRscEVMxGuv7UYanyMSnp+fI6pIfAKfcme/tGGKYiiF6biHVmDKcL+tnYloZvuDvfM+
T7k1vMIf9UcX9ZglJu+6B1N7ZRV8wO9ZKCHcTeVkNqbTu7clhsjjEjwO/EWQrPv7aZPSu8hcJr/dFfP3
AskvvG04rgAAAIEAjS61ZiP1iGoP0UhJCf4uHDnGra41mvMyqGBFwji93XON49UmVYXVFfYcWeoDzpaH
JQguFttMCNduiXmZfDYITld+86c9aWCR6g7re977ElFTbutWe+isu/ZFINXOvDEHmBUKd7++4lGDCjsM
NOQQmG/Ftsi4jE2iWBaI91oyTQI= opid00@lisgeiger1
ssh-rsa AAAAB3NzaC1yc2EAAAABIwAAAQEAxHKsWjHzIsIt0Pt1lkZA9Px5x0v6e2ZzCh+AEiQz1nk0
l7kU6K0IzKvYbAj6HnQB3/epYHz6SBRrpsMQcFPHgtQIKlTzeKHNqS6pHBKxKR77jGGq70i7SWZsSBXP
1/8QxUhV9CNbFJKAkEmvXa5ZO1fKgtiXYXR26X72foOKwZzOtPzOqz2IQ6icxqTMELK1H4R+s0Rvuurl
lDibdzo5g3xuV9bu/HLYt19zUgIR0KoTzpZEyPSiNwNizUy5oqXiNL4ZdcCjsSwQ1lYDwbzrg5brQA8W
onqu5dtK4/LSh97jJ7u2V7LCUPr1KZj7OUy1FOHg2MUUjJbJApAMAffXgQ== root@pc6698
ssh-rsa AAAAB3NzaC1yc2EAAAABIwAAAQEA2cWXxdmZHHfBq0n7iE4aNB6iyHWIUSA1EbLbuCfGhSog
cn+uTeRXdAQfBvHXAp2JbR+mX30ftMzq28TfWlMKPWvKgcEwh05WbhL9swRIj7+FTryxnZG+LDDpIAUg
kaGEmrX/9gtQ0wBwsbWPPPuHP6rlvSfoX2QPl6DSEt4AJqKf2QJNfm1SdqpQZOK5bG77VcEt3GRob9Mu
d4j9Y+Tb8CWnruDQl6+Z66ccWwjCI5mlhKkjzgkaJytURcvEP4y+htqpeW6maoXJmvtS900+SCv1dqTe
lbiSd2hRMx2ElZ7WCdaspHwkxwYyDtaPyHrGYuunDUhLFk+nDBjCUcuFgQ== theidel@pc6698
ssh-dss AAAAB3NzaC1kc3MAAACBALeM8Rw5A/3q3oWqP8OuVU1H12nL+UxQiHlpQj/rQ1C02+O1x3SZ
M32gJZo99s8uFb2YTlbzxYDroLdxw5Z1fM22Dsf9vUDcNcAWfXQK0JV2LIsNLJKC/s3/O51GwvtgxtC4
wMgG3MMe5kmyI34tJSuVMggcnBepssvH6oWGVNbJAAAAFQCbtQeAikwu20rUfn7eEiCOP/0p9wAAAIBE
hXhaxl5Ht29VldHfYMMAjY3V1+d2XbleLl7ixOdQLcy2igssBR4w0QRz4V6p0ePCiIhzqiWf5Hvgc1u/
TBK0Rj9STI1qU1s8A6x/qdNDTbgebSeO6CNGqDTvhIdMgX7dUhgtwx4lzgbKtOtYSZ1XkMr1omwMAK9n
K7xFCNu4IAAAAIBS0Is0ryjPYiOuEnWptKy9FiBYv2edS3vJ3Ln74HjzJ8FW3jT76xwEiBcaBtvXZ5kM
VLyDtR3LR63i11Nnrg7nNJa43S4sng9dbBnO3f5/7Ylv2ku/vhATtMouVRn8c+xP1CMEYpGhSIw+OzrG
xs33FGKr0xkL2yofwrDtHNRA/Q== theidel@pc6698
ssh-dss AAAAB3NzaC1kc3MAAACBALGVR0qC2i/HgaJl4fuiwmOVrq46Bz3bs+o3/jdw/dqMaPjx35Ha
shyC4zS+2wHyZVSjwTMIbVT8LPsNMGxL40ZxqWaAUyzn0XnjJMe3XT7h+yyx+iLUXvyCK489PAwT0srE
iWbGNeQTgEYiwX+jqezQTiwss2sgypOrrwIrGrZBAAAAFQDjOUdgHjbCc1UMW37Zu+7b/AV1cQAAAIAu
tumVMJlCqWv30RRscEVMxGuv7UYanyMSnp+fI6pIfAKfcme/tGGKYiiF6biHVmDKcL+tnYloZvuDvfM+
T7k1vMIf9UcX9ZglJu+6B1N7ZRV8wO9ZKCHcTeVkNqbTu7clhsjjEjwO/EWQrPv7aZPSu8hcJr/dFfP3
AskvvG04rgAAAIEAjS61ZiP1iGoP0UhJCf4uHDnGra41mvMyqGBFwji93XON49UmVYXVFfYcWeoDzpaH
JQguFttMCNduiXmZfDYITld+86c9aWCR6g7re977ElFTbutWe+isu/ZFINXOvDEHmBUKd7++4lGDCjsM
NOQQmG/Ftsi4jE2iWBaI91oyTQI= opid00@lisgeiger1
Check that all the keys are identical:
lisgeiger1:~/eiger/psi_eiger_500k_024_025/2018-04-01-1828 % \
md5sum ssh_authorized_keys_beb*
1c183bdaa3a2f27029fca84b9cb3b857 ssh_authorized_keys_beb024
1c183bdaa3a2f27029fca84b9cb3b857 ssh_authorized_keys_beb025
In case the opid00@lisgeiger1 public key is not included (not the case before), add them in order to open SSH sessions automatically on the detector modules:
lisgeiger1:~/eiger/psi_eiger_500k_024_025/2018-04-01-1828 % \
if grep -q 'opid00@lisgeiger1' ssh_authorized_keys_beb*; then
echo "SSH keys already installed in detector ${SLS_DETECTOR_NAME}"
else
echo "Installing SSH keys in detector ${SLS_DETECTOR_NAME}"
for m in ${SLS_DETECTOR_MODULES}; do
ssh -x root@${m} sh -c '"cat >> .ssh/authorized_keys"' \
< ${SLS_DETECTORS_DIR}/eiger/ssh/id_dsa.pub
done
fi
Also check that the SSH public host keys are identical (same Linux image):
lisgeiger1:~/eiger/psi_eiger_500k_024_025/2018-04-01-1828 % \
for m in ${SLS_DETECTOR_MODULES}; do
ssh-keygen -f ~/.ssh/known_hosts -F ${m} -l
done
# Host beb024 found: line 82 type RSA
1040 21:78:5d:39:d5:cc:92:7a:42:f8:4d:69:38:3b:40:40 |1|m9PYbOqjp0h4qI8tq9u9H8x7pKQ=|wXZou5Y2oMKiULF5ZOuBjV0U7oo= (RSA)
# Host beb025 found: line 84 type RSA
1040 21:78:5d:39:d5:cc:92:7a:42:f8:4d:69:38:3b:40:40 |1|Hp2vpbDpXlxTjMSfxo+n+r3B+ZQ=|LaI693N3AKzUER5lgBOOwReHOpI= (RSA)
eigerDetectorServer
Before transferring the new version of the eigerDetectorServer, keep track of the current versions stored on the modules:
lisgeiger1:~/eiger/psi_eiger_500k_024_025/2018-04-01-1828 % \
server_dir="executables"
server_name="eigerDetectorServer"
server="${server_dir}/${server_name}"
server_str=$(echo ${server} | sed 's:/:_:g')
full_server="/home/root/${server}"
for m in ${SLS_DETECTOR_MODULES}; do
ssh -x root@${m} 'ls -l '${server}'*' \
> ls_${server_str}_${m}.out
done
cat ls_${server_str}_${EIGER_MODULE_TOP}.out
echo
for m in ${SLS_DETECTOR_MODULES}; do
ssh -x root@${m} 'md5sum '${server}'*' \
> md5sum_${server_str}_${m}.out
done
cat md5sum_${server_str}_${EIGER_MODULE_TOP}.out
echo
md5sum md5sum_${server_str}_beb*
-rwxr-xr-x 1 root root 280601 Jan 1 01:15 executables/eigerDetectorServer
-rwxr-xr-x 1 root root 277442 Aug 26 2016 executables/eigerDetectorServer_bkp
-rwxr-xr-x 1 root root 277442 Aug 26 2016 executables/eigerDetectorServerv2.0.5.14.3
-rwxr-xr-x 1 root root 280601 Jan 1 01:14 executables/eigerDetectorServerv2.3.0.16.2
4fca193db64ed991da785043e7769082 executables/eigerDetectorServer
e8a39956bbcb4aac62f109188e8ddbb2 executables/eigerDetectorServer_bkp
e8a39956bbcb4aac62f109188e8ddbb2 executables/eigerDetectorServerv2.0.5.14.3
4fca193db64ed991da785043e7769082 executables/eigerDetectorServerv2.3.0.16.2
754a871d0608c28aa7544230ca728f86 md5sum_executables_eigerDetectorServer_beb024.out
754a871d0608c28aa7544230ca728f86 md5sum_executables_eigerDetectorServer_beb025.out
Kill the running servers and disable the automatic startup:
lisgeiger1:~/eiger/psi_eiger_500k_024_025/2018-04-01-1828 % \
for m in ${SLS_DETECTOR_MODULES}; do
ssh -x root@${m} killall ${server_name}
done
for m in ${SLS_DETECTOR_MODULES}; do
ssh -x root@${m} sed -i '"s:^#\?\('${full_server}'\).*$:#\1 \&:"' \
/etc/init.d/board_com.sh
done
Force a filesystem sync on each host to make the changes persistent, just before power-cycling:
lisgeiger1:~/eiger/psi_eiger_500k_024_025/2018-04-01-1828 % \
for m in ${SLS_DETECTOR_MODULES}; do
ssh -x root@${m} sync
done
Power-cycle the detector and check that no eigerDetectorServer is running:
lisgeiger1:~/eiger/psi_eiger_500k_024_025/2018-04-01-1828 % \
for m in ${SLS_DETECTOR_MODULES}; do \
ssh -x root@${m} 'ps -ef | grep '${server}' | grep -v grep'; \
done
Backup the current version, and transfer the new version:
lisgeiger1:~/eiger/psi_eiger_500k_024_025/2018-04-01-1828 % \
for m in ${SLS_DETECTOR_MODULES}; do
ssh -x root@${m} 'mv '${server}' '${server}'_bkp'
done
SLS_DETECTOR_PACKAGE=${LIMA_DIR}/camera/slsdetector/slsDetectorPackage
new_servers=$(cd ${SLS_DETECTOR_PACKAGE} && find -name ${server_name}v\*)
(cd ${SLS_DETECTOR_PACKAGE} && md5sum ${new_servers})
echo
new_server=${SLS_DETECTOR_PACKAGE}/$(echo "${new_servers}" | head -n 1)
for m in ${SLS_DETECTOR_MODULES}; do
scp ${new_server} root@${m}:${server_dir}
done
for m in ${SLS_DETECTOR_MODULES}; do
ssh -x root@${m} "cp ${server_dir}/$(basename ${new_server}) ${server}"
done
50ef053f1ddd0b49314479a558c9c330 ./slsDetectorSoftware/eigerDetectorServer/bin/eigerDetectorServerv3.1.1.16.0
50ef053f1ddd0b49314479a558c9c330 ./serverBin/eigerDetectorServerv3.1.1.16.0
eigerDetectorServerv3.1.1.16.0 100% 286KB 286.2KB/s 00:00
eigerDetectorServerv3.1.1.16.0 100% 286KB 286.2KB/s 00:00
Check that all is as expected:
lisgeiger1:~/eiger/psi_eiger_500k_024_025/2018-04-01-1828 % \
cd
this_dir="${base_dir}/$(date +%Y-%m-%d-%H%M)"
mkdir -p ${this_dir} && cd ${this_dir}
for m in ${SLS_DETECTOR_MODULES}; do
ssh -x root@${m} 'ls -l '${server}'*' \
> ls_${server_str}_${m}.out
done
cat ls_${server_str}_${EIGER_MODULE_TOP}.out
echo
for m in ${SLS_DETECTOR_MODULES}; do
ssh -x root@${m} 'md5sum '${server}'*' \
> md5sum_${server_str}_${m}.out
done
cat md5sum_${server_str}_${EIGER_MODULE_TOP}.out
echo
md5sum md5sum_${server_str}_beb*
-rwxr-xr-x 1 root root 293085 Jan 10 02:35 executables/eigerDetectorServer
-rwxr-xr-x 1 root root 280601 Jan 1 01:15 executables/eigerDetectorServer_bkp
-rwxr-xr-x 1 root root 277442 Aug 26 2016 executables/eigerDetectorServerv2.0.5.14.3
-rwxr-xr-x 1 root root 280601 Jan 1 01:14 executables/eigerDetectorServerv2.3.0.16.2
-rwxr-xr-x 1 root root 293085 Jan 10 02:34 executables/eigerDetectorServerv3.1.1.16.0
50ef053f1ddd0b49314479a558c9c330 executables/eigerDetectorServer
4fca193db64ed991da785043e7769082 executables/eigerDetectorServer_bkp
e8a39956bbcb4aac62f109188e8ddbb2 executables/eigerDetectorServerv2.0.5.14.3
4fca193db64ed991da785043e7769082 executables/eigerDetectorServerv2.3.0.16.2
50ef053f1ddd0b49314479a558c9c330 executables/eigerDetectorServerv3.1.1.16.0
4168a104e53ee71f763ed5f0e0b43859 md5sum_executables_eigerDetectorServer_beb024.out
4168a104e53ee71f763ed5f0e0b43859 md5sum_executables_eigerDetectorServer_beb025.out
Force a another filesystem sync:
lisgeiger1:~/eiger/psi_eiger_500k_024_025/2018-04-01-1927 % \
cd
for m in ${SLS_DETECTOR_MODULES}; do
ssh -x root@${m} sync
done
And finally perform a paranoid check after power-cycling the detector:
lisgeiger1:~ % \
prev_dir=${this_dir}
this_dir="${base_dir}/$(date +%Y-%m-%d-%H%M)"
mkdir -p ${this_dir} && cd ${this_dir}
for m in ${SLS_DETECTOR_MODULES}; do
ssh -x root@${m} 'md5sum '${server}'*' \
> md5sum_${server_str}_${m}.out
done
cd ..
for m in ${SLS_DETECTOR_MODULES}; do
(diff ${prev_dir}/md5sum_${server_str}_${m}.out ${this_dir} &&
echo "${m} OK" || echo "${m} changed")
done
beb024 OK
beb025 OK
Firmware flash
Note
older modules beb021/020 (Eiger-500k #1) and beb074/071/064/102/072/073/087/088 (Eiger-2M) use bigger Xilinx Virtex5 FX70T FPGAs in Front-End-Board (FEB). New modules like beb024/025 (Eiger-500k #2) use in their FEBs Xilinx Virtex5 FX30T FPGAs. Updated: The module beb024/025 FEBs were changed during its front-end update with Xilinx Virtex5 FX70T FPGAs. No automatic determination of the FPGA type can be performed by software. Solved: the flash.config file includes the Feb section with the FpgaType, which is used by the code below.
The current FWs (v18 and later) allow entering into flash mode from the Linux environment, without the need of pressing the button in the rear panel. The latestversion of the eiger_flash utility exploits this and enters into flash mode automatically.
Note
two BEB FWs variants allow using fiber optic or twisted-pair (copper) transceivers: beb_fiber.bit and beb_copper.bit. The good file must be specified in the command below.
Run the eiger_flash utility to update the FEB left/right and BEB FWs, as well as the kernel image:
lisgeiger1:~ % (
[ -n "${SLS_DETECTOR_MODULES}" ] || . ${SLS_DETECTORS_DIR}/common/scripts/det_env_setup.sh;
base_dir="${SLS_DETECTOR_LOG}/${SLS_DETECTOR_NAME}";
detector_dir="${SLS_DETECTOR_CONFIG_DIR}/setup/${SLS_DETECTOR_BACKEND_SETUP}/detector";
fw_ver=$(cat ${detector_dir}/fw);
fw_dir="${SLS_DETECTORS_DIR}/slsDetectorFirmware/binaries/eiger/${fw_ver}";
flash_config="${detector_dir}/flash.config";
fpga_type=$(python <<EOF
from configparser import ConfigParser
c = ConfigParser()
c.read("${flash_config}")
print(f'{c["Feb"]["FpgaType"].lower()}')
EOF
);
kernel_opt="";
kernel_image="${fw_dir}/simpleImage.virtex440-eiger-beb-hwid1_local";
[ -f ${kernel_image} ] && kernel_opt="-k ${kernel_image}";
this_dir="${base_dir}/$(date +%Y-%m-%d-%H%M)";
mkdir -p ${this_dir};
eiger_flash -c ${flash_config} \
-m ${fw_dir}/beb_fiber.bit \
-l ${fw_dir}/feb_l_${fpga_type}.bit \
-r ${fw_dir}/feb_r_${fpga_type}.bit ${kernel_opt} \
-o ${this_dir}/eiger_flash.log ${SLS_DETECTOR_MODULES};
)
Eiger flash - Fri Sep 11 16:17:11 2020
9ad0445fc4958ff780cc85998b5bf968 fw/v24/beb_fiber.bit
0e872295daaf42278219dc938550daba fw/v24/feb_l_fx70t.bit
437976fee26a47bb6e9884adf10d5d77 fw/v24/feb_r_fx70t.bit
1f27879faa7082f9ed2bb2b24b84ea99 fw/v24/simpleImage.virtex440-eiger-beb-hwid1_local
Connecting to Extreme Switch esmgmt ...
Getting status of ports 1,2 ...
Quitting ...
Done!
[beb109] Executing: nc -p 3000 -u beb109 3000
[beb116] Executing: nc -p 3000 -u beb116 3000
[beb109] Not in firmware flash mode ... ping'ing ...
[beb116] Not in firmware flash mode ... ping'ing ...
[beb109] ping OK ... Check ssh ...
[beb116] ping OK ... Check ssh ...
[beb109] Checking flash-mode setup files ...
[beb116] Checking flash-mode setup files ...
[beb109] Starting flash-mode (boot_recovery) ...
[beb116] Starting flash-mode (boot_recovery) ...
[beb109] Waiting for flash-mode (20 sec) ...
[beb116] Waiting for flash-mode (20 sec) ...
[beb109] Restarting Ethernet connection ...
[beb116] Restarting Ethernet connection ...
Connecting to Extreme Switch esmgmt ...
Restarting ports 1,2 ...
Quitting ...
Done!
Connecting to Extreme Switch esmgmt ...
Disabling Auto-Negotiation on ports 1,2 ...
Quitting ...
Done!
[beb116] Waiting for connection (10 sec) ...
[beb109] Waiting for connection (10 sec) ...
Connecting to Extreme Switch esmgmt ...
Getting status of ports 1,2 ...
Quitting ...
Done!
[beb109] Executing: nc -p 3000 -u beb109 3000
[beb116] Executing: nc -p 3000 -u beb116 3000
[beb109] Entered into flash-mode OK!
[beb116] Entered into flash-mode OK!
[beb116] Executing: xterm -title Eiger beb116 console -e cat /tmp/eiger_flash_con_pipe.beb116
[beb109] Executing: xterm -title Eiger beb109 console -e cat /tmp/eiger_flash_con_pipe.beb109
[beb116] Uploading MAIN_BIT fw/v24/beb_fiber.bit to /fw0 (4923823 bytes)
[beb109] Uploading MAIN_BIT fw/v24/beb_fiber.bit to /fw0 (4923823 bytes)
[beb116] Transferred MAIN_BIT bit file fw/v24/beb_fiber.bit (took 2.1 sec)
[beb116] Waiting for firmware flash to finish ...
[beb109] Transferred MAIN_BIT bit file fw/v24/beb_fiber.bit (took 2.4 sec)
[beb109] Waiting for firmware flash to finish ...
[beb109] Firmware flash finished OK (took 35.1 sec)
[beb116] Firmware flash finished OK (took 38.8 sec)
[beb116] Uploading LEFT_BIT fw/v24/feb_l_fx70t.bit to /febl (3378270 bytes)
[beb109] Uploading LEFT_BIT fw/v24/feb_l_fx70t.bit to /febl (3378270 bytes)
[beb116] Transferred LEFT_BIT bit file fw/v24/feb_l_fx70t.bit (took 1.7 sec)
[beb116] Waiting for firmware flash to finish ...
[beb109] Transferred LEFT_BIT bit file fw/v24/feb_l_fx70t.bit (took 1.8 sec)
[beb109] Waiting for firmware flash to finish ...
[beb109] Firmware flash finished OK (took 181.3 sec)
[beb116] Firmware flash finished OK (took 182.2 sec)
[beb116] Uploading RIGHT_BIT fw/v24/feb_r_fx70t.bit to /febr (3378271 bytes)
[beb109] Uploading RIGHT_BIT fw/v24/feb_r_fx70t.bit to /febr (3378271 bytes)
[beb116] Transferred RIGHT_BIT bit file fw/v24/feb_r_fx70t.bit (took 1.7 sec)
[beb116] Waiting for firmware flash to finish ...
[beb109] Transferred RIGHT_BIT bit file fw/v24/feb_r_fx70t.bit (took 1.7 sec)
[beb109] Waiting for firmware flash to finish ...
[beb109] Firmware flash finished OK (took 185.5 sec)
[beb116] Firmware flash finished OK (took 186.8 sec)
[beb116] Uploading KERNEL_LOCAL fw/v24/simpleImage.virtex440-eiger-beb-hwid1_local to /kernel (2068980 bytes)
[beb109] Uploading KERNEL_LOCAL fw/v24/simpleImage.virtex440-eiger-beb-hwid1_local to /kernel (2068980 bytes)
[beb116] Transferred KERNEL_LOCAL bit file fw/v24/simpleImage.virtex440-eiger-beb-hwid1_local (took 1.1 sec)
[beb116] Waiting for firmware flash to finish ...
[beb109] Transferred KERNEL_LOCAL bit file fw/v24/simpleImage.virtex440-eiger-beb-hwid1_local (took 1.1 sec)
[beb109] Waiting for firmware flash to finish ...
[beb109] Firmware flash finished OK (took 13.5 sec)
[beb116] Firmware flash finished OK (took 14.2 sec)
Connecting to Extreme Switch esmgmt ...
Enabling Auto-Negotiation on ports 1,2 ...
Quitting ...
Done!
Press any key to quit ...
Showing in the console for the FX70T FW:
*** Output from beb116 console ***
TFTP WRQ (write request): /fw0
Receiving bitfile for parallel flash location 0
transfer done: total len = 4923823
field 3 key='a' len= 46 system.ncd;HW_TIMEOUT=FALSE;UserID=0xFFFFFFFF
field 4 key='b' len= 15 5vfx100tff1136
field 5 key='c' len= 11 2019/12/18
field 6 key='d' len= 9 15:29:55
field 7 len=4923712
Doing bitswap for Parallel Flash...done
XFlash_Unlock()
XFlash_Erase()
XFlash_Write()
Compare
XFlash_Lock()
Success
TFTP WRQ (write request): /febl
Receiving bitfile for spi flash feb left
transfer done: total len = 3378270
field 3 key='a' len= 31 feb_left.ncd;UserID=0xFFFFFFFF
field 4 key='b' len= 13 5vfx70tff665
field 5 key='c' len= 11 2019/07/29
field 6 key='d' len= 9 14:54:29
field 7 len=3378176
Copying to WriteBuffer...done
Chip Erase Starting
address = 0x00000000
end_address = 0x00330000
len = 3378176
Chip Erase Complete
Writing
done.. Now reading back
Compare
Success
TFTP WRQ (write request): /febr
Receiving bitfile for spi flash feb right
transfer done: total len = 3378271
field 3 key='a' len= 32 feb_right.ncd;UserID=0xFFFFFFFF
field 4 key='b' len= 13 5vfx70tff665
field 5 key='c' len= 11 2019/07/29
field 6 key='d' len= 9 14:57:22
field 7 len=3378176
Copying to WriteBuffer...done
Chip Erase Starting
address = 0x00000000
end_address = 0x00330000
len = 3378176
Chip Erase Complete
Writing
done.. Now reading back
Compare
Success
TFTP WRQ (write request): /kernel
Receiving linux kernel
transfer done: total len = 2068980
Linux Kernel: len=2068980
XFlash_Unlock()
XFlash_Erase()
XFlash_Write()
Compare
XFlash_Lock()
Success
Start the eigerDetectorServer and check that everything is OK:
lisgeiger1:~ % \
for m in ${SLS_DETECTOR_MODULES}; do
ssh -x root@${m} 'nohup '${server}' > /dev/null 2>&1 &'
done
Once verified that the new server runs fine with the new firmware, restore automatic startup:
lisgeiger1:~ % \
for m in ${SLS_DETECTOR_MODULES}; do
ssh -x root@${m} sed -i '"s:^#\?\('${full_server}'\).*$:\1 \&:"' \
/etc/init.d/board_com.sh
done
for m in ${SLS_DETECTOR_MODULES}; do
ssh -x root@${m} sync
done
Power-cycle the detector and verify that the servers start automatically:
lisgeiger1:~ % \
for m in ${SLS_DETECTOR_MODULES}; do \
ssh -x root@${m} 'ps -ef | grep '${server}' | grep -v grep'; \
done
961 root 0:00 /home/root/executables/eigerDetectorServer
965 root 0:00 /home/root/executables/eigerDetectorServer -stopserver
961 root 0:00 /home/root/executables/eigerDetectorServer
965 root 0:00 /home/root/executables/eigerDetectorServer -stopserver